How Pipe Relining Works: The Engineering Behind Trenchless Pipe Repair
Cured-in-place pipe relining turns a cracked, root-filled drain into a new composite pipe without digging a trench. Here is what is actually happening underground, and why it works.
Most of the sewer and stormwater pipes under Australian homes were laid decades ago in vitrified clay, earthenware, concrete or cast iron. They rarely fail all at once. Joints open up, roots find the gaps, corrosion thins the walls and the ground shifts around them. For a long time the only fix was to excavate and replace. Pipe relining, more formally cured-in-place pipe (CIPP), offers another route: build a new pipe inside the old one.
It is a good case study for engineering students because it pulls together polymer chemistry, composite materials, structural mechanics, hydraulics and asset management in a single, very practical job.
A short history
CIPP was developed in London in 1971, when engineer Eric Wood relined a Victorian-era brick sewer with a resin-impregnated felt tube. The method has since become one of the most widely used trenchless rehabilitation techniques in the world, used on everything from 100 mm house drains to large municipal sewers.
Why old pipes fail
Understanding the failure modes explains both why relining works and where it does not.
- Joint failure and root intrusion. Clay and earthenware pipes come in short lengths joined with mortar or early rubber rings. Over time the joints crack or the rings perish, letting moisture out and fine tree roots in. Roots then grow into dense mats that catch waste and block the line.
- Sulphide corrosion. In sewers, bacteria in the slime layer produce hydrogen sulphide gas. Other bacteria on the pipe crown oxidise it to sulphuric acid, which attacks concrete and cementitious linings from the inside.
- Ground movement. Reactive clay soils, common across much of south-east Queensland, swell when wet and shrink when dry. That seasonal movement cracks rigid pipes and pulls joints apart.
- Corrosion of metal pipes. Cast iron and galvanised steel lose wall thickness to corrosion until they crack or hole through.
The relining process, step by step
- CCTV inspection. A camera is pushed through the line to map its length, diameter, bends, branch connections and defects. This is the basis for deciding whether relining is suitable at all.
- Cleaning. High-pressure water jetting and mechanical root cutters remove roots, scale and debris so the liner can bond to, or at least sit tight against, the host pipe.
- Liner preparation. A flexible tube of felt (polyester needle felt) or fibreglass is cut to length and saturated with a thermosetting resin, usually a two-part epoxy for house drains. This step is called wet-out, and the resin quantity is calculated from the liner volume.
- Installation. The wet liner is either inverted into the pipe with air or water pressure, turning inside out as it travels, or pulled into place and then inflated with a bladder. Either way it is pressed hard against the host pipe wall.
- Curing. The resin is hardened while the liner is held under pressure. Depending on the system, curing is done at ambient temperature, with hot water or steam, or with ultraviolet light for fibreglass liners. Heat and UV cut the cure time from hours to minutes.
- Reinstating connections. The liner seals over branch connections, so a remote cutting robot reopens each junction from inside the pipe.
- Final CCTV. A second camera run confirms the liner is continuous, wrinkle-free and that every connection has been reopened.
“Most of the drains we put a camera down around Logan are old clay or earthenware lines with roots coming through the joints. If the pipe still holds its shape and the fall is right, relining is usually the better fix: we clean it out, line it, and the driveway and garden stay exactly where they are. If the camera shows a collapsed section or a big sag, we tell the homeowner straight that it needs to be dug up, because a liner just follows whatever shape the old pipe is in.”
— The team at Logan Plumbing & Gas, licensed plumbers and drainers in Logan, Queensland
The engineering inside the liner
A composite pipe
Once cured, the liner is a fibre-reinforced polymer composite: the felt or glass fibres carry tensile load and the resin matrix binds them and seals the wall. The result is a jointless, corrosion-resistant pipe formed to the exact shape of the host.
Structural design
Designers treat the old pipe in one of two ways. If the host pipe is partially deteriorated, it is assumed to still carry soil and traffic loads, and the liner mainly has to resist external groundwater pressure and bridge holes and open joints. If the host is fully deteriorated, the liner must carry soil, live and groundwater loads by itself. In both cases the critical failure mode is usually buckling of a thin-walled tube under external pressure, so wall thickness is driven by the liner's flexural modulus, its long-term (creep-reduced) properties, any ovality in the host pipe, and a safety factor.
Hydraulics
A liner a few millimetres thick slightly reduces the internal diameter, which on its own would reduce capacity. In practice the smooth, jointless polymer surface has a much lower roughness than old clay or corroded concrete, and it removes the steps and root obstructions at every joint. For many pipes the flow capacity after relining is similar to, or better than, the deteriorated pipe it replaces.
Standards and approvals in Australia
Relining products used in private sanitary drainage need WaterMark certification, and the work must meet the Plumbing Code of Australia and AS/NZS 3500.2. Work on water authority sewers is governed by the relevant authority and the WSA codes. In Queensland, drainage work, including relining, must be done by a licensed plumber or drainer.
Where relining is the wrong answer
- Collapsed or badly broken pipe. The liner needs a continuous host to be installed through and pressed against.
- Sags and poor grade. The liner follows the existing pipe, so a belly that holds water before relining will still hold water afterwards.
- Severe offsets. Large displaced joints can stop the liner passing or cause wrinkles and fins in the cured wall.
- Sharp bends and changes in diameter. Some systems handle these well, others do not, and the CCTV survey decides it.
In those cases a short excavated repair, a patch liner on a single defect, pipe bursting or a full replacement may be the better engineering choice. Often the answer is a combination: dig and fix the one collapsed section, then reline the rest.
Why it matters for engineering education
Trenchless rehabilitation is a useful teaching example because the trade-offs are real and measurable. Students can compare whole-of-life cost, carbon from excavation and spoil haulage, disruption to residents and traffic, and the uncertainty of design life (manufacturers commonly cite around 50 years for CIPP). It also shows how much good engineering depends on inspection data. Nearly every decision about a relining job comes from what the camera shows.
For more on how engineering is taught and researched across the region, explore the Australasian Journal of Engineering Education archive or read about AAEE.